Dextrose and Sodium Chloride description, usages, side effects, indications, overdosage, supplying and lots more!

Menu
Search

Dextrose and Sodium Chloride

Baxter Healthcare Corporation

Dextrose and Sodium Chloride Injection, USP in VIAFLEX Plastic Container


FULL PRESCRIBING INFORMATION: CONTENTS*




FULL PRESCRIBING INFORMATION

DEXTROSE AND SODIUM CHLORIDE DESCRIPTION

Dextrose and Sodium Chloride Injection, USP is a sterile, nonpyrogenic solution for fluid and electrolyte replenishment and caloric supply in single dose containers for intravenous administration. It contains no antimicrobial agents. Composition, osmolarity, pH, ionic concentration and caloric content are shown in Table 1.

Table 1
Size (mL) Composition (g/L) Normal physiologic osmolarity range is approximately 280 to 310 mOsmol/L.Osmolarity (mOsmol/L) (calc.) pH Ionic Concentration (mEq/L) Caloric Content (kcal/L)
**Dextrose Hydrous, USP Sodium Chloride, USP (NaCl) Sodium Chloride
2.5% Dextrose and 0.45% Sodium Chloride Injection, USP 500 1000 25 4.5 280 4.5
(3.2 to 6.5)
77 77 85
5% Dextrose and 0.2% Sodium Chloride Injection, USP 250 500 1000 50 2 321 4.0
(3.2 to 6.5)
34 34 170
5% Dextrose and 0.33% Sodium Chloride Injection, USP 250 500 1000 50 3.3 365 4.0
(3.2 to 6.5)
56 56 170
5% Dextrose and 0.45% Sodium Chloride Injection, USP 250 500 1000 50 4.5 406 4.0
(3.2 to 6.5)
77 77 170
5% Dextrose and 0.9% Sodium Chloride Injection, USP 250 500 1000 50 9 560 4.0
(3.2 to 6.5)
154 154 170
10% Dextrose and 0.9% Sodium Chloride Injection, USP 500 1000 100 9 813 4.0
(3.2 to 6.5)
154 154 340
Dextrose and Sodium Chloride

The VIAFLEX plastic container is fabricated from a specially formulated polyvinyl chloride (PL 146 Plastic). The amount of water that can permeate from inside the container into the overwrap is insufficient to affect the solution significantly. Solutions in contact with the plastic container can leach out certain of its chemical components in very small amounts within the expiration period, e.g., di-2-ethylhexyl phthalate (DEHP), up to 5 parts per million. However, the safety of the plastic has been confirmed in tests in animals according to USP biological tests for plastic containers as well as by tissue culture toxicity studies.

CLINICAL PHARMACOLOGY

Dextrose and Sodium Chloride Injection, USP has value as a source of water, electrolytes, and calories. It is capable of inducing diuresis depending on the clinical condition of the patient.

DEXTROSE AND SODIUM CHLORIDE INDICATIONS AND USAGE

Dextrose and Sodium Chloride Injection, USP is indicated as a source of water, electrolytes, and calories.

DEXTROSE AND SODIUM CHLORIDE CONTRAINDICATIONS

Solutions containing dextrose may be contraindicated in patients with known allergy to corn or corn products.

WARNINGS

Dextrose and Sodium Chloride Injection, USP should be used with great care, if at all, in patients with congestive heart failure, severe renal insufficiency, and in clinical states in which there exists edema with sodium retention.

Dextrose injections with low electrolyte concentrations should not be administered simultaneously with blood through the same administration set because of the possibility of pseudoagglutination or hemolysis. The container label for these injections bears the statement: Do not administer simultaneously with blood.

The intravenous administration of Dextrose and Sodium Chloride Injection, USP can cause fluid and/or solute overloading resulting in dilution of serum electrolyte concentrations, overhydration, congested states, or pulmonary edema. The risk of dilutional states is inversely proportional to the electrolyte concentrations of the injections. The risk of solute overload causing congested states with peripheral and pulmonary edema is directly proportional to the electrolyte concentrations of the injections.

Excessive administration of Dextrose and Sodium Chloride Injection, USP may result in significant hypokalemia.

In patients with diminished renal function, administration of Dextrose and Sodium Chloride Injection, USP may result in sodium retention.

PRECAUTIONS

Do not use plastic containers in series connections. Such use could result in air embolism due to residual air being drawn from the primary container before administration of the fluid from the secondary container is completed. Pressurizing intravenous solutions contained in flexible plastic containers to increase flow rates can result in air embolism if the residual air in the container is not fully evacuated prior to administration.

Use of a vented intravenous administration set with the vent in the open position could result in air embolism. Vented intravenous administration sets with the vent in the open position should not be used with flexible plastic containers.

Dextrose and Sodium Chloride Injection, USP should be used with caution in patients with overt or subclinical diabetes mellitus.

Administration of hypertonic solutions may cause venous irritation, including phlebitis. Hyperosmolar solutions should be administered with caution, if at all, to patients with hyperosmolar states. See Table 1 in the DESCRIPTION section for the osmolarities of the Dextrose and Sodium Chloride Injection, USP solutions.

Laboratory Tests

 Clinical evaluation and periodic laboratory determinations are necessary to monitor changes in fluid balance, electrolyte concentrations, and acid base balance during prolonged parenteral therapy or whenever the condition of the patient warrants such evaluation.

Drug Interactions

Caution must be exercised in the administration of Dextrose and Sodium Chloride Injection, USP to patients receiving corticosteroids or corticotropin.

Carcinogenesis, Mutagenesis, Impairment of Fertility

Studies with Dextrose and Sodium Chloride Injection, USP have not been performed to evaluate carcinogenic potential, mutagenic potential, or effects on fertility.

Pregnancy: Teratogenic Effects

Pregnancy Category C. Animal reproduction studies have not been conducted with Dextrose and Sodium Chloride Injection, USP. It is also not known whether Dextrose and Sodium Chloride Injection, USP can cause fetal harm when administered to a pregnant woman or can affect reproduction capacity. Dextrose and Sodium Chloride Injection, USP should be given to a pregnant woman only if clearly needed.

Nursing Mothers

It is not known whether this drug is excreted in human milk. Because many drugs are excreted in human milk, caution should be exercised when Dextrose and Sodium Chloride Injection, USP is administered to a nursing mother.

Pediatric Use

The use of Dextrose and Sodium Chloride Injection, USP in pediatric patients is based on clinical practice.

Newborns – especially those born premature and with low birth weight – are at increased risk of developing hypo– or hyperglycemia and therefore need close monitoring during treatment with intravenous glucose solutions to ensure adequate glycemic control in order to avoid potential long term adverse effects. Hypoglycemia in the newborn can cause prolonged seizures, coma and brain damage. Hyperglycemia has been associated with intraventricular hemorrhage, late onset bacterial and fungal infection, retinopathy of prematurity, necrotizing enterocolitis, bronchopulmonary dysplasia, prolonged length of hospital stay, and death.

Plasma electrolyte concentrations should be closely monitored in the pediatric population as this population may have impaired ability to regulate fluids and electrolytes.

The infusion of hypotonic fluids together with the non-osmotic secretion of ADH may result in hyponatremia in patients with acute volume depletion. Hyponatremia can lead to headache, nausea, seizures, lethargy, coma, cerebral edema and death, therefore acute symptomatic hyponatremic encephalopathy is considered a medical emergency (applies to solutions containing less than 0.9% sodium chloride).

Geriatric Use

Clinical studies of Dextrose and Sodium Chloride Injection, USP did not include sufficient numbers of subjects aged 65 and over to determine whether they respond differently from younger subjects. Other reported clinical experience has not identified differences in responses between the elderly and younger patients. In general, dose selection for an elderly patient should be cautious, usually starting at the low end of the dosing range, reflecting the greater frequency of decreased hepatic, renal, or cardiac function, and of concomitant disease or other drug therapy.

Do not administer unless solution is clear and seal is intact.

ADVERSE REACTIONS

- Hypersensitivity reactions, including anaphylaxis and chills

- Hyponatremia (applies to solutions containing less than 0.9% Sodium Chloride)

Reactions which may occur because of the solution or the technique of administration include febrile response, infection at the site of injection, venous thrombosis or phlebitis extending from the site of injection, extravasation and hypervolemia.

If an adverse reaction does occur, discontinue the infusion, evaluate the patient, institute appropriate therapeutic countermeasures and save the remainder of the fluid for examination if deemed necessary.

DEXTROSE AND SODIUM CHLORIDE DOSAGE AND ADMINISTRATION

As directed by a physician. Dosage is dependent upon the age, weight, and clinical condition of the patient as well as laboratory determinations. Parenteral drug products should be inspected visually for particulate matter and discoloration prior to administration whenever solution and container permit.

All injections in VIAFLEX plastic containers are intended for intravenous administration using sterile equipment.

The dosage and constant infusion rate of intravenous dextrose must be selected with caution in pediatric patients, particularly neonates and low weight infants, because of the increased risk of hyperglycemia/hypoglycemia. The infusion rate and volume depends on the age, weight, clinical and metabolic conditions of the patient, concomitant therapy and should be determined by the consulting physician experienced in pediatric intravenous fluid therapy.

Additives may be incompatible. Complete information is not available.

Those additives known to be incompatible should not be used. Consult with pharmacist, if available. If, in the informed judgment of the physician, it is deemed advisable to introduce additives, use aseptic technique. Mix thoroughly when additives have been introduced. Do not store solutions containing additives.

HOW SUPPLIED

Dextrose and Sodium Chloride Injection, USP in VIAFLEX plastic container is supplied as follows:

Code Size (mL) NDC Product Name
2B1023 500 0338-0073-03 2.5% Dextrose and 0.45% Sodium Chloride Injection, USP
2B1024 1000 0338-0073-04
2B1092 250 0338-0077-02 5% Dextrose and 0.2% Sodium Chloride Injection, USP
2B1093 500 0338-0077-03
2B1094 1000 0338-0077-04
2B1082 250 0338-0081-02 5% Dextrose and 0.33% Sodium Chloride Injection, USP
2B1083 500 0338-0081-03
2B1084 1000 0338-0081-04
2B1072 250 0338-0085-02 5% Dextrose and 0.45% Sodium Chloride Injection, USP
2B1073 500 0338-0085-03
2B1074 1000 0338-0085-04
2B1062 250 0338-0089-02 5% Dextrose and 0.9% Sodium Chloride Injection, USP
2B1063 500 0338-0089-03
2B1064 1000 0338-0089-04
2B1163 500 0338-0095-03 10% Dextrose and 0.9% Sodium Chloride Injection, USP
2B1164 1000 0338-0095-04

Exposure of pharmaceutical products to heat should be minimized. Avoid excessive heat. It is recommended the product be stored at room temperature (25°C); brief exposure up to 40°C does not adversely affect the product.

DIRECTIONS FOR USE OF VIAFLEX PLASTIC CONTAINER

To Open

Tear overwrap down side at slit and remove solution container. Some opacity of the plastic due to moisture absorption during the sterilization process may be observed. This is normal and does not affect the solution quality or safety. The opacity will diminish gradually. Check for minute leaks by squeezing inner bag firmly. If leaks are found, discard solution as sterility may be impaired. If supplemental medication is desired, follow directions below.

Preparation for Administration

  • Suspend container from eyelet support.
  • Remove protector from outlet port at bottom of container.
  • Attach administration set. Refer to complete directions accompanying set.

To Add Medication

WARNING

Additives may be incompatible.

  • Prepare medication site.
  • Using syringe with 19 to 22 gauge needle, puncture resealable medication port and inject.
  • Mix solution and medication thoroughly. For high density medication such as potassium chloride, squeeze ports while ports are upright and mix thoroughly.
  • Close clamp on the set.
  • Prepare medication site.
  • Using syringe with 19 to 22 gauge needle, puncture resealable medication port and inject.
  • Remove container from IV pole and/or turn to an upright position.
  • Evacuate both ports by squeezing them while container is in the upright position.
  • Mix solution and medication thoroughly.
  • Return container to in use position and continue administration.

Baxter Healthcare Corporation
Deerfield, IL 60015 USA

Printed in USA

*For Bar Code Position Only
071970015

07-19-70-015  Rev.  September 2013

BAXTER, VIAFLEX and PL 146 are trademarks of
Baxter International Inc.

PACKAGE LABELING - PRINCIPAL DISPLAY PANEL

 

Container Label

LOT EXP

2B1062
NDC 0338-0089-02

5% Dextrose and
0.9% Sodium Chloride
Injection USP

250 mL EACH 100 mL CONTAINS
5 g DEXTROSE HYDROUS
USP 900 mg SODIUM CHLORIDE USP
pH 4.0 (3.2 TO 6.5) mEq/L SODIUM 154
CHLORIDE 154 HYPERTONIC OSMOLARITY
560 mOsmol/L (CALC) STERILE
NONPYROGENIC SINGLE DOSE CONTAINER
ADDITIVES MAY BE INCOMPATIBLE CONSULT
WITH PHARMACIST IF AVAILABLE WHEN
INTRODUCING ADDITIVES USE ASEPTIC
TECHNIQUE MIX THOROUGHLY DO NOT
STORE DOSAGE INTRAVENOUSLY AS
DIRECTED BY A PHYSICIAN SEE DIRECTIONS
CAUTIONS SQUEEZE AND INSPECT INNER
BAG WHICH MAINTAINS PRODUCT STERILITY
DISCARD IF LEAKS ARE FOUND MUST NOT
BE USED IN SERIES CONNECTIONS DO NOT
USE UNLESS SOLUTION IS CLEAR RX ONLY
STORE UNIT IN MOISTURE BARRIER
OVERWRAP AT ROOM TEMPERATURE
(25°C/77°F) UNTIL READY TO USE AVOID
EXCESSIVE HEAT SEE INSERT

VIAFLEX CONTAINER PL 146 PLASTIC

BAXTER VIAFLEX AND PL 146 ARE
TRADEMARKS OF BAXTER INTERNATIONAL INC

BAXTER Logo

BAXTER HEALTHCARE CORPORATION

DEERFIELD IL 60015 USA

MADE IN USA

FOR PRODUCT INFORMATION 1-800-933-0303

50

100

150

200

07-25-31-365

Carton Label

2B1063Q 36-500 ML

VIAFLEX® CONTAINER

5% DEXTROSE AND
0.9% SODIUM CHLORIDE INJ, USP

EXP
XXXXX

SECONDARY BAR CODE
(17) YYMM00 (10) XXXXX

LOT
XXXXX

PRIMARY BAR CODE
(01) 50303380089029

Dextrose and Sodium Chloride

2B1023
NDC 0338-0073-03
DIN 00060720

2.5% Dextrose and
0.9% Sodium Chloride
Injection USP

500 mL

EACH 100 mL CONTAINS 2.5 g DEXTROSE HYDROUS USP 450
mg SODIUM CHLORIDE USP pH 4.0 (3.2 TO 6.5) mEq/L
SODIUM 77 CHLORIDE 77 HYPERTONIC OSMOLARITY 280 mOsmol/L
(CALC) STERILE NONPYROGENIC SINGLE DOSE CONTAINER
ADDITIVES MAY BE INCOMPATIBLE CONSULT WITH PHARMACIST IF
AVAILABLE WHEN INTRODUCING ADDITIVES USE ASEPTIC
TECHNIQUE MIX THOROUGHLY DO NOT STORE DOSAGE
INTRAVENOUSLY AS DIRECTED BY A PHYSICIAN SEE DIRECTIONS
CAUTIONS SQUEEZE AND INSPECT INNER BAG WHICH MAINTAINS
PRODUCT STERILITY DISCARD IF LEAKS ARE FOUND MUST NOT
BE USED IN SERIES CONNECTIONS DO NOT USE UNLESS SOLUTION
IS CLEAR RX ONLY STORE UNIT IN MOISTURE BARRIER OVERWRAP
AT ROOM TEMPERATURE (25°C/77°F) UNTIL READY TO USE AVOID
EXCESSIVE HEAT SEE INSERT

Baxter Logo

BAXTER HEALTHCARE CORPORATION
DEERFIELD IL 60015 USA
MADE IN USA

DISTRIBUTED IN CANADA BY
BAXTER CORPORATION
TORONTO ONTARIO CANADA

VIAFLEX CONTAINER
PL 146 PLASTIC

FOR PRODUCT INFORMATION
1-800-933-0303

BAXTER VIAFLEX AND
PL 146 ARE TRADEMARKS OF
BAXTER INTERNATIONAL INC

07-25-38-743

1

2

3

4

Carton Label

2B1023Q 24-500 ML

VIAFLEX® CONTAINER

2.5% DEXTROSE AND
0.45% SODIUM CHLORIDE INJ, USP

EXP
XXXXX

SECONDARY BAR CODE
(17) XXXXX (10) XXXXX

LOT
XXXXX

PRIMARY BAR CODE
(01) 50303380073035

Container Label

LOT EXP

2B1062
NDC 0338-0089-02

5% Dextrose and
0.9% Sodium Chloride
Injection USP

250 mL EACH 100 mL CONTAINS
5 g DEXTROSE HYDROUS
USP 900 mg SODIUM CHLORIDE USP
pH 4.0 (3.2 TO 6.5) mEq/L SODIUM 154
CHLORIDE 154 HYPERTONIC OSMOLARITY
560 mOsmol/L (CALC) STERILE
NONPYROGENIC SINGLE DOSE CONTAINER
ADDITIVES MAY BE INCOMPATIBLE CONSULT
WITH PHARMACIST IF AVAILABLE WHEN
INTRODUCING ADDITIVES USE ASEPTIC
TECHNIQUE MIX THOROUGHLY DO NOT
STORE DOSAGE INTRAVENOUSLY AS
DIRECTED BY A PHYSICIAN SEE DIRECTIONS
CAUTIONS SQUEEZE AND INSPECT INNER
BAG WHICH MAINTAINS PRODUCT STERILITY
DISCARD IF LEAKS ARE FOUND MUST NOT
BE USED IN SERIES CONNECTIONS DO NOT
USE UNLESS SOLUTION IS CLEAR RX ONLY
STORE UNIT IN MOISTURE BARRIER
OVERWRAP AT ROOM TEMPERATURE
(25°C/77°F) UNTIL READY TO USE AVOID
EXCESSIVE HEAT SEE INSERT

VIAFLEX CONTAINER PL 146 PLASTIC

BAXTER VIAFLEX AND PL 146 ARE
TRADEMARKS OF BAXTER INTERNATIONAL INC

BAXTER Logo

BAXTER HEALTHCARE CORPORATION

DEERFIELD IL 60015 USA

MADE IN USA

FOR PRODUCT INFORMATION 1-800-933-0303

50

100

150

200

07-25-31-365

Carton Label

2B1092Q 36-250 ML

VIAFLEX® CONTAINER

5% DEXTROSE AND
0.2% SODIUM CHLORIDE INJ, USP

EXP
XXXXX

SECONDARY BAR CODE
(17) YYMM00 (10) XXXXX

LOT
XXXXX

PRIMARY BAR CODE
(01) 50303380077026

Container Label

LOT EXP

2B1083
NDC 0338-0081-03

5% Dextrose and
0.33% Sodium Chloride
Injection USP

500 mL

EACH 100 mL CONTAINS 5 g DEXTROSE HYDROUS USP
330 mg SODIUM CHLORIDE USP pH 4.0 (3.2 TO 6.5)
mEq/L SODIUM 56 CHLORIDE 56 OSMOLARITY 356
mOsmol/L (CALC) STERILE NONPYROGENIC SINGLE DOSE
CONTAINER ADDITIVES MAY BE INCOMPATIBLE CONSULT WITH
PHARMACIST IF AVAILABLE WHEN INTRODUCING ADDITIVES USE
ASEPTIC TECHNIQUE MIX THOROUGHLY DO NOT STORE
DOSAGE INTRAVENOUSLY AS DIRECTED BY A PHYSICIAN SEE
DIRECTIONS CAUTIONS SQUEEZE AND INSPECT INNER BAG
WHICH MAINTAINS PRODUCT STERILITY DISCARD IF LEAKS ARE
FOUND MUST NOT BE USED IN SERIES CONNECTIONS DO NOT
USE UNLESS SOLUTION IS CLEAR RX ONLY STORE UNIT IN
MOISTURE BARRIER OVERWRAP T ROOM TEMPERATURE
(25°C/77°F) UNTIL READY TO USE AVOID EXCESSIVE HEAT
SEE INSERT

VIAFLEX CONTAINER PL 146 PLASTIC

BAXTER VIAFLEX AND PL 146 ARE TRADEMARKS OF
BAXTER INTERNATIONAL INC

 FOR PRODUCT INFORMATION 1-800-933-0303

Baxter Logo
BAXTER HEALTHCARE CORPORATION
DEERFIELD IL 60015 USA

MADE IN USA

07-25-34-096

1

2

3

4

Dextrose and Sodium Chloride

2B1083Q 24-500 ML

VIAFLEX® CONTAINER

5% DEXTROSE AND
0.33% SODIUM CHLORIDE INJ, USP

EXP
XXXXX

SECONDARY BAR CODE
(17) XXXXX (10) XXXXX

LOT
XXXXX

PRIMARY BAR CODE
(01) 50303380081030

Container Label

LOT EXP

2B1072
NDC 0338-0085-02

5% Dextrose and
0.45% Sodium Chloride
Injection USP

250 mL EACH 100 mL CONTAINS
5 g DEXTROSE HYDROUS
USP 450 mg SODIUM CHLORIDE USP
pH 4.0 (3.2 TO 6.5) mEq/L SODIUM 77
CHLORIDE 77 HYPERTONIC OSMOLARITY
406 mOsmol/L (CALC) STERILE
NONPYROGENIC SINGLE DOSE CONTAINER
ADDITIVES MAY BE INCOMPATIBLE CONSULT
WITH PHARMACIST IF AVAILABLE WHEN
INTRODUCING ADDITIVES USE ASEPTIC
TECHNIQUE MIX THOROUGHLY DO NOT
STORE DOSAGE INTRAVENOUSLY AS
DIRECTED BY A PHYSICIAN SEE DIRECTIONS
CAUTIONS SQUEEZE AND INSPECT INNER
BAG WHICH MAINTAINS PRODUCT STERILITY
DISCARD IF LEAKS ARE FOUND MUST NOT BE
USED IN SERIES CONNECTIONS DO NOT USE
UNLESS SOLUTION IS CLEAR RX ONLY
STORE UNIT IN MOISTURE BARRIER
OVERWRAP AT ROOM TEMPERATURE
(25°C/77°F) UNTIL READY TO USE AVOID
EXCESSIVE HEAT SEE INSERT

VIAFLEX CONTAINER PL 146 PLASTIC

BAXTER VIAFLEX AND PL 146 ARE
TRADEMARKS OF BAXTER INTERNATIONAL INC

FOR PRODUCT INFORMATION
1-800-933-0303

BAXTER Logo

BAXTER HEALTHCARE CORPORATION

DEERFIELD IL 60015 USA

MADE IN USA

50

100

150

200

07-25-31-441

Carton Label

2B1072Q 36-250 ML

VIAFLEX® CONTAINER

5% DEXTROSE AND
0.45% SODIUM CHLORIDE INJ, USP

EXP
XXXXX

SECONDARY BAR CODE
(17) YYMM00 (10) XXXXX

LOT
XXXXX

PRIMARY BAR CODE
(01) 50303380085021

Dextrose and Sodium Chloride

LOT EXP

2B1164
NDC 0338-0095-04

10% Dextrose and
0.9% Sodium Chloride
Injection USP

1000 mL

EACH 100 mL CONTAINS 10 g DEXTROSE HYDROUS USP 900
mg SODIUM CHLORIDE USP pH 4.0 (3.2 TO 6.5) mEq/L
SODIUM 154 CHLORIDE 154 OSMOLARITY 813 mOsmol/L
(CALC) HYPERTONIC MAY CAUSE VEIN DAMAGE STERILE
NONPYROGENIC SINGLE DOSE CONTAINER ADDITIVES MAY BE
INCOMPATIBLE CONSULT WITH PHARMACIST IF AVAILABLE WHEN INTRODUCING ADDITIVES USE ASEPTIC TECHNIQUE MIX
THOROUGHLY DO NOT STORE DOSAGE INTRAVENOUSLY AS
DIRECTED BY A PHYSICIAN SEE DIRECTIONS CAUTIONS SQUEEZE
AND INSPECT INNER BAG WHICH MAINTAINS PRODUCT STERILITY
DISCARD IF LEAKS ARE FOUND MUST NOT BE USED IN SERIES
CONNECTIONS DO NOT USE UNLESS SOLUTION IS CLEAR
FEDERAL (USA) LAW PROHIBITS DISPENSING WITHOUT
PRESCRIPTION STORE UNIT IN MOISTURE BARRIER OVERWRAP AT
ROOM TEMPERATURE (25°C/77°F) UNTIL READY TO USE AVOID
EXCESSIVE HEAT SEE INSERT

Baxter Logo
BAXTER HEALTHCARE CORPORATION
DEERFIELD IL 60015 USA

MADE IN USA

Viaflex® CONTAINER
PL 146® PLASTIC

 FOR PRODUCT INFORMATION
CALL 1-800-933-0303

07-25-02-859

1

2

3

4

5

6

7

8

9

Carton Label

2B1164 12-1000 ML

VIAFLEX CONTAINER

10% DEXTROSE AND
0.9% SODIUM CHLORIDE INJ, USP

EXP
XXXXX

SECONDARY BAR CODE
(17) YYMM00 (10) XXXXX

LOT
XXXXX

PRIMARY BAR CODE
(01) 50303380095044

Dextrose and Sodium Chloride

Dextrose and Sodium Chloride INJECTION, SOLUTION

Product Information

Product Type Human prescription drug label Item Code (Source) NDC:0338-0073
Route of Administration INTRAVENOUS DEA Schedule

Active Ingredient/Active Moiety

Ingredient Name Basis of Strength Strength
Dextrose monohydrate ANHYDROUS DEXTROSE 2.5 g
SODIUM CHLORIDE 450 mg

Packaging

# Item Code Package Description Marketing Start Date Marketing End Date
1 NDC:0338-0073-03 500 in 1 BAG
2 NDC:0338-0073-04 1000 in 1 BAG

Marketing Information

Marketing Category Application Number or Monograph Citation Marketing Start Date Marketing End Date
NDA NDA016697 1971-03-22


Dextrose and Sodium Chloride

Dextrose and Sodium Chloride INJECTION, SOLUTION

Product Information

Product Type Human prescription drug label Item Code (Source) NDC:0338-0077
Route of Administration INTRAVENOUS DEA Schedule

Active Ingredient/Active Moiety

Ingredient Name Basis of Strength Strength
Dextrose monohydrate ANHYDROUS DEXTROSE 5 g
SODIUM CHLORIDE 200 mg

Packaging

# Item Code Package Description Marketing Start Date Marketing End Date
1 NDC:0338-0077-02 250 in 1 BAG
2 NDC:0338-0077-03 500 in 1 BAG
3 NDC:0338-0077-04 1000 in 1 BAG

Marketing Information

Marketing Category Application Number or Monograph Citation Marketing Start Date Marketing End Date
NDA NDA016689 1970-12-08


Dextrose and Sodium Chloride

Dextrose and Sodium Chloride INJECTION, SOLUTION

Product Information

Product Type Human prescription drug label Item Code (Source) NDC:0338-0081
Route of Administration INTRAVENOUS DEA Schedule

Active Ingredient/Active Moiety

Ingredient Name Basis of Strength Strength
Dextrose monohydrate ANHYDROUS DEXTROSE 5 g
SODIUM CHLORIDE 330 mg

Packaging

# Item Code Package Description Marketing Start Date Marketing End Date
1 NDC:0338-0081-02 250 in 1 BAG
2 NDC:0338-0081-03 500 in 1 BAG
3 NDC:0338-0081-04 1000 in 1 BAG

Marketing Information

Marketing Category Application Number or Monograph Citation Marketing Start Date Marketing End Date
NDA NDA016687 1971-03-22


Dextrose and Sodium Chloride

Dextrose and Sodium Chloride INJECTION, SOLUTION

Product Information

Product Type Human prescription drug label Item Code (Source) NDC:0338-0085
Route of Administration INTRAVENOUS DEA Schedule

Active Ingredient/Active Moiety

Ingredient Name Basis of Strength Strength
Dextrose monohydrate ANHYDROUS DEXTROSE 5 g
SODIUM CHLORIDE 450 mg

Packaging

# Item Code Package Description Marketing Start Date Marketing End Date
1 NDC:0338-0085-02 250 in 1 BAG
2 NDC:0338-0085-03 500 in 1 BAG
3 NDC:0338-0085-04 1000 in 1 BAG

Marketing Information

Marketing Category Application Number or Monograph Citation Marketing Start Date Marketing End Date
NDA NDA016683 1971-03-22


Dextrose and Sodium Chloride

Dextrose and Sodium Chloride INJECTION, SOLUTION

Product Information

Product Type Human prescription drug label Item Code (Source) NDC:0338-0089
Route of Administration INTRAVENOUS DEA Schedule

Active Ingredient/Active Moiety

Ingredient Name Basis of Strength Strength
Dextrose monohydrate ANHYDROUS DEXTROSE 5 g
SODIUM CHLORIDE 900 mg

Packaging

# Item Code Package Description Marketing Start Date Marketing End Date
1 NDC:0338-0089-02 250 in 1 BAG
2 NDC:0338-0089-03 500 in 1 BAG
3 NDC:0338-0089-04 1000 in 1 BAG

Marketing Information

Marketing Category Application Number or Monograph Citation Marketing Start Date Marketing End Date
NDA NDA016678 1970-12-09


Dextrose and Sodium Chloride

Dextrose and Sodium Chloride INJECTION, SOLUTION

Product Information

Product Type Human prescription drug label Item Code (Source) NDC:0338-0095
Route of Administration INTRAVENOUS DEA Schedule

Active Ingredient/Active Moiety

Ingredient Name Basis of Strength Strength
Dextrose monohydrate ANHYDROUS DEXTROSE 10 g
SODIUM CHLORIDE 900 mg

Packaging

# Item Code Package Description Marketing Start Date Marketing End Date
1 NDC:0338-0095-03 500 in 1 BAG
2 NDC:0338-0095-04 1000 in 1 BAG

Marketing Information

Marketing Category Application Number or Monograph Citation Marketing Start Date Marketing End Date
NDA NDA016696 1971-03-22


PLEASE, BE CAREFUL!
Be sure to consult your doctor before taking any medication!
Copyright © 2014. drugs-library.com. All rights reserved. Information on drugs-library.com is provided for educational purposes only and is not to be used for medical advice, diagnosis or treatment.
Support info@drugs-library.com.